Freescale Semiconductor Computer Accessories EETX4K User Manual

DOCUMENT NUMBER  
S12EETX4KV0  
Freescale Semiconductor, Inc.  
EETX4K  
Block Guide  
V00.04  
Original Release Date: 7 JUL 2003  
Revised: 30 OCT 2003  
Motorola, Inc.  
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its  
products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,  
including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in  
different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s  
technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as  
components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the  
Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized  
application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses,  
and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges  
that Motorola was negligent regarding the design or manufacture of the part. Motorola and  
Opportunity/Affirmative Action Employer.  
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal  
©Motorola, Inc., 2001  
1
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Table of Contents  
EADDR — EEPROM Address Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
3
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
List of Figures  
Figure 3-11 EEPROM Address Low Register (EADDRLO) . . . . . . . . . . . . . . . . . . . . . . . 23  
Figure 3-12 EEPROM Data High Register (EDATAHI). . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Figure 3-13 EEPROM Data Low Register (EDATALO) . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
5
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
6
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
8
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
9
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
10  
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Section 1 Introduction  
1.1 Overview  
This document describes the EETX4K module which includes a 4K byte EEPROM (Non-Volatile)  
memory. The EEPROM memory may be read as either bytes, aligned words or misaligned words. Read  
access time is one bus cycle for bytes and aligned words, and two bus cycles for misaligned words.  
The EEPROM memory is ideal for data storage for single-supply applications allowing for field  
reprogramming without requiring external voltage sources for program or erase. Program and erase  
functions are controlled by a command driven interface. The EEPROM module supports both block erase  
(all memory bytes) and sector erase (4 memory bytes). An erased bit reads ‘1’ and a programmed bit reads  
‘0’. The high voltage required to program and erase the EEPROM memory is generated internally. It is not  
possible to read from the EEPROM block while it is being erased or programmed.  
NOTE: An EEPROM word (2 bytes) must be erased before being programmed. Cumulative  
programming of bits within a word is not allowed.  
1.1.1 Glossary  
Command Write Sequence  
A three-step MCU instruction sequence to execute built-in algorithms (including program and erase) on  
the EEPROM memory.  
1.2 Features  
4K bytes of EEPROM memory divided into 1024 sectors of 4 bytes.  
Automated program and erase algorithm.  
Interrupts on EEPROM command completion and command buffer empty.  
Fast sector erase and word program operation.  
2-stage command pipeline.  
Sector erase abort feature for critical interrupt response.  
Flexible protection scheme to prevent accidental program or erase.  
Single power supply for all EEPROM operations including program and erase.  
1.3 Modes of Operation  
Program, erase and erase verify operations (please refer to section 4.1 for details).  
11  
For More Information On This Product,  
           
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
1.4 Block Diagram  
A block diagram of the EEPROM module is shown in Figure 1-1.  
EETX4K  
EEPROM  
Interface  
Command  
Interrupt  
Command Pipeline  
Request  
EEPROM  
cmd1  
addr1  
data1  
cmd2  
addr2  
data2  
2K * 16 Bits  
sector 0  
sector 1  
Registers  
Protection  
sector 1023  
Oscillator  
Clock  
Clock  
Divider  
EECLK  
Figure 1-1 Module Block Diagram  
12  
For More Information On This Product,  
   
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Section 2 External Signal Description  
2.1 Overview  
The EEPROM module contains no signals that connect off-chip.  
13  
For More Information On This Product,  
   
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Section 3 Memory Map and Registers  
3.1 Overview  
This section describes the memory map and registers for the EEPROM module.  
3.2 Module Memory Map  
A linear EEPROM memory map is shown in Figure 3-1. The HCS12X architecture actually places the  
EEPROM memory addresses between logical addresses $0800 and $1000 with $0800 to $0BFF  
representing 1K byte of paged EEPROM memory and $0C00 to $0FFF representing 1K byte of fixed  
EEPROM memory. The EPROT register, described in section 3.3.5, can be set to protect the upper region  
in the EEPROM memory from accidental program or erase. The EEPROM addresses covered by this  
protectable region are shown in the EEPROM memory map. The default protection setting is stored in the  
EEPROM configuration field as described in Table 3-1.  
Table 3-1 EEPROM Configuration Field  
EEPROM Memory  
Address Offset  
Size  
(bytes)  
Description  
$_FFC  
Reserved  
1
1
2
EEPROM Protection byte  
Refer to Section 3.3.5 EPROT —  
$_FFD  
$_FFE - $_FFF  
Reserved  
14  
For More Information On This Product,  
       
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
ADDRESS OFFSET = $_00  
EEPROM Registers  
12 bytes  
ADDRESS OFFSET = $_0B  
EEPROM BASE + $_000  
EEPROM Memory  
3584 bytes (up to 4032 bytes)  
+ $_E00  
+ $_E40  
+ _$E80  
+ $_EC0  
EEPROM Memory Protected Region  
64, 128, 192, 256, 320, 384, 448, 512 bytes  
+ $_F00  
+ $_F40  
+ $_F80  
+ $_FC0  
EEPROM Configuration Field  
16 bytes ($_FFC - $_FFF)  
EEPROM BASE + $_FFF  
Figure 3-1 EEPROM Memory Map  
15  
For More Information On This Product,  
 
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
The EEPROM module also contains a set of 12 control and status registers located between EEPROM  
register address offsets $_00 and $_0B. A summary of the EEPROM module registers is given in Table  
3-2 while their accessibility is detailed in section 3.3.  
Table 3-2 EEPROM Register Map  
Address  
Offset  
Normal Mode  
Access  
Register Name  
$_00  
$_01  
EEPROM Clock Divider Register (ECLKDIV)  
R/W  
R
1
RESERVED1  
$_02  
$_03  
$_04  
$_05  
$_06  
$_07  
R
RESERVED2  
EEPROM Configuration Register (ECNFG)  
EEPROM Protection Register (EPROT)  
EEPROM Status Register (ESTAT)  
R/W  
R/W  
R/W  
R/W  
R
EEPROM Command Register (ECMD)  
RESERVED3  
$_08  
$_09  
R
R
R
R
EEPROM High Address Register (EADDRHI)  
EEPROM Low Address Register (EADDRLO)  
$_0A  
EEPROM High Data Register (EDATAHI)  
$_0B  
EEPROM Low Data Register (EDATALO)  
NOTES:  
1. Intended for factory test purposes only.  
NOTE: Register Address = EEPROM Control Register Base Address + Address Offset,  
where the EEPROM Control Register Base Address is defined at the MCU level and  
the Address Offset is defined at the EEPROM module level.  
16  
For More Information On This Product,  
   
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
3.3 Register Descriptions  
3.3.1 ECLKDIV — EEPROM Clock Divider Register  
The ECLKDIV register is used to control timed events in program and erase algorithms.  
Address Offset: $_00  
7
6
PRDIV8  
0
5
EDIV5  
0
4
EDIV4  
0
3
EDIV3  
0
2
EDIV2  
0
1
EDIV1  
0
0
EDIV0  
0
R
W
EDIVLD  
RESET:  
0
= Unimplemented or Reserved  
Figure 3-2 EEPROM Clock Divider Register (ECLKDIV)  
All bits in the ECLKDIV register are readable, bits 6-0 are write once and bit 7 is not writable.  
EDIVLD — Clock Divider Loaded.  
1 = Register has been written to since the last reset.  
0 = Register has not been written.  
PRDIV8 — Enable Prescalar by 8.  
1 = Enables a prescalar by 8, to divide the oscillator clock before feeding into the clock divider.  
0 = The oscillator clock is directly fed into the ECLKDIV divider.  
EDIV[5:0] — Clock Divider Bits.  
The combination of PRDIV8 and EDIV[5:0] effectively divides the EEPROM module input oscillator  
clock down to a frequency of 150kHz - 200kHz. The maximum divide ratio is 512. Please refer to  
section 4.1.1 for more information.  
3.3.2 RESERVED1  
This register is reserved for factory testing and is not accessible.  
Address Offset: $_01  
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
W
0
0
0
0
0
0
0
0
Reset:  
= Unimplemented or Reserved  
Figure 3-3 RESERVED1  
All bits read zero and are not writable.  
17  
For More Information On This Product,  
                 
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
3.3.3 RESERVED2  
This register is reserved for factory testing and is not accessible.  
Address Offset: $_02  
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
W
Reset:  
0
0
0
0
0
0
0
0
= Unimplemented or Reserved  
Figure 3-4 RESERVED2  
All bits read zero and are not writable.  
3.3.4 ECNFG — EEPROM Configuration Register  
The ECNFG register enables the EEPROM interrupts.  
Address Offset: $_03  
7
CBEIE  
0
6
CCIE  
0
5
0
4
0
3
0
2
0
1
0
0
0
R
W
0
0
0
0
0
0
Reset:  
= Unimplemented or Reserved  
Figure 3-5 EEPROM Configuration Register (ECNFG)  
CBEIE and CCIE bits are readable and writable while all remaining bits read zero and are not writable.  
CBEIE — Command Buffer Empty Interrupt Enable.  
The CBEIE bit enables an interrupt in case of an empty command buffer in the EEPROM module.  
0 = Command Buffer Empty interrupt disabled.  
CCIE — Command Complete Interrupt Enable.  
The CCIE bit enables an interrupt in case all commands have been completed in the EEPROM module.  
1 = An interrupt will be requested whenever the CCIF flag (see 3.3.6 ESTAT — EEPROM Status  
0 = Command Complete interrupt disabled.  
18  
For More Information On This Product,  
             
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
3.3.5 EPROT — EEPROM Protection Register  
The EPROT register defines which EEPROM sectors are protected against program or erase operations.  
Address Offset: $_04  
7
EPOPEN  
F
6
5
4
3
EPDIS  
F
2
EPS2  
F
1
EPS1  
F
0
EPS0  
F
R
W
RNV6  
RNV5  
RNV4  
F
F
F
Reset:  
= Unimplemented or Reserved  
Figure 3-6 EEPROM Protection Register (EPROT)  
All bits in the EPROT register are readable and writable except for RNV[6:4] which are only readable.  
The EPOPEN and EPDIS bits can only be written to the protected state. The EPS bits can be written  
anytime until bit EPDIS is cleared. If the EPOPEN bit is cleared, the state of the EPDIS and EPS bits is  
irrelevant.  
During the reset sequence, the EPROT register is loaded from the EEPROM Protection byte at address  
will be loaded during the reset sequence, the EEPROM memory must be unprotected, then the EEPROM  
Protection byte must be reprogrammed. Trying to alter data in any protected area in the EEPROM memory  
will result in a protection violation error and the PVIOL flag will be set in the ESTAT register. The mass  
erase of an EEPROM block is possible only when protection is fully disabled by setting the EPOPEN and  
EPDIS bits.  
EPOPEN — Opens the EEPROM for program or erase.  
1 = The EEPROM sectors not protected are enabled for program or erase.  
0 = The entire EEPROM memory is protected from program and erase.  
RNV[6:4] — Reserved Non-Volatile Bits.  
The RNV[6:4] bits should remain in the erased state “1” for future enhancements.  
EPDIS — EEPROM Protection address range Disable.  
The EPDIS bit determines whether there is a protected area in a specific region of the EEPROM  
memory ending with address offset $_FFF.  
1 = Protection disabled.  
0 = Protection enabled.  
EPS[2:0] — EEPROM Protection Address Size.  
The EPS[2:0] bits determine the size of the protected area as shown inTable 3-3. The EPS bits can  
only be written to while the EPDIS bit is set.  
19  
For More Information On This Product,  
             
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Table 3-3 EEPROM Protection Address Range  
Address Offset  
EPS[2:0]  
Protected Size  
Range  
000  
001  
010  
011  
100  
101  
110  
111  
$_FC0-$_FFF  
$_F80-$_FFF  
$_F40-$_FFF  
$_F00-$_FFF  
$_EC0-$_FFF  
$_E80-$_FFF  
$_E40-$_FFF  
$_E00-$_FFF  
64 bytes  
128 bytes  
192 bytes  
256 bytes  
320 bytes  
384 bytes  
448 bytes  
512 bytes  
3.3.6 ESTAT — EEPROM Status Register  
The ESTAT register defines the operational status of the module.  
Address Offset: $_05  
7
CBEIF  
1
6
5
PVIOL  
0
4
ACCERR  
0
3
0
2
1
0
0
0
R
W
CCIF  
BLANK  
1
0
0
0
0
Reset:  
= Unimplemented or Reserved  
Figure 3-7 EEPROM Status Register (ESTAT)  
CBEIF, PVIOL and ACCERR are readable and writable, CCIF and BLANK are readable and not writable,  
remaining bits read zero and are not writable.  
CBEIF — Command Buffer Empty Interrupt Flag.  
The CBEIF flag indicates that the address, data and command buffers are empty so that a new  
command write sequence can be started. The CBEIF flag is cleared by writing a “1” to CBEIF. Writing  
a “0” to the CBEIF flag has no effect on CBEIF. Writing a “0” to CBEIF after writing an aligned word  
to the EEPROM address space but before CBEIF is cleared will abort a command write sequence and  
cause the ACCERR flag to be set. Writing a “0” to CBEIF outside of a command write sequence will  
not set the ACCERR flag. The CBEIF flag is used together with the CBEIE bit in the ECNFG register  
to generate an interrupt request (see Figure 4-8).  
1 = Buffers are ready to accept a new command.  
0 = Buffers are full.  
CCIF — Command Complete Interrupt Flag.  
20  
For More Information On This Product,  
           
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
The CCIF flag indicates that there are no more commands pending. The CCIF flag is cleared when  
CBEIF is clear and sets automatically upon completion of all active and pending commands. The CCIF  
flag does not set when an active commands completes and a pending command is fetched from the  
command buffer. Writing to the CCIF flag has no effect on CCIF. The CCIF flag is used together with  
the CCIE bit in the ECNFG register to generate an interrupt request (see Figure 4-8).  
1 = All commands are completed.  
0 = Command in progress.  
PVIOL — Protection Violation Flag.  
The PVIOL flag indicates an attempt was made to program or erase an address in a protected area of  
the EEPROM memory during a command write sequence. The PVIOL flag is cleared by writing a “1”  
to PVIOL. Writing a “0” to the PVIOL flag has no effect on PVIOL. While PVIOL is set, it is not  
possible to launch a command or start a command write sequence.  
1 = A protection violation has occurred.  
0 = No failure.  
ACCERR — Access Error Flag.  
The ACCERR flag indicates an illegal access has occurred to the EEPROM memory caused by either  
a violation of the command write sequence (see section 4.1.2), issuing an illegal EEPROM command  
(see Table 3-4), launching the sector erase abort command terminating a sector erase operation early  
(see section 4.1.3.5) or the execution of a CPU STOP instruction while a command is executing  
(CCIF=0). The ACCERR flag is cleared by writing a “1” to ACCERR. Writing a “0” to the ACCERR  
flag has no effect on ACCERR. While ACCERR is set, it is not possible to launch a command or start  
a command write sequence. If ACCERR is set by an erase verify operation, any buffered command  
will not launch.  
1 = Access error has occurred.  
0 = No access error detected.  
BLANK — Flag indicating the erase verify operation status.  
When the CCIF flag is set after completion of an erase verify command, the BLANK flag indicates the  
result of the erase verify operation. The BLANK flag is cleared by the EEPROM module when CBEIF  
is cleared as part of a new valid command write sequence. Writing to the BLANK flag has no effect  
on BLANK.  
1 = EEPROM block verified as erased.  
0 = EEPROM block verified as not erased.  
3.3.7 ECMD — EEPROM Command Register  
The ECMD register is the EEPROM command register.  
21  
For More Information On This Product,  
         
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Address Offset: $_06  
7
0
6
0
5
0
4
0
3
CMDB  
0
2
0
1
0
0
0
R
W
0
Reset:  
= Unimplemented or Reserved  
Figure 3-8 EEPROM Command Register (ECMD)  
All CMDB bits are readable and writable during a command write sequence while bit 7 reads zero and is  
not writable.  
CMDB[6:0] — Valid EEPROM commands are shown in Table 3-4. Writing any command other than  
those listed in Table 3-4 sets the ACCERR flag in the ESTAT register.  
Table 3-4 Valid EEPROM Command List  
CMDB[6:0]  
$05  
Command  
Erase Verify  
$20  
Word Program  
Sector Erase  
Mass Erase  
$40  
$41  
$47  
Sector Erase Abort  
Sector Modify  
$60  
3.3.8 RESERVED3  
This register is reserved for factory testing and is not accessible.  
Address Offset: $_07  
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
W
0
0
0
0
0
0
0
0
Reset:  
= Unimplemented or Reserved  
Figure 3-9 RESERVED3  
All bits read zero and are not writable.  
22  
For More Information On This Product,  
         
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
3.3.9 EADDR — EEPROM Address Registers  
The EADDRHI and EADDRLO registers are the EEPROM address registers.  
Address Offset: $_08  
7
0
6
0
5
4
3
2
0
1
0
0
R
EABHI  
0
0
0
W
0
0
0
0
0
0
Reset:  
= Unimplemented or Reserved  
Figure 3-10 EEPROM Address High Register (EADDRHI)  
Address Offset: $_09  
7
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
W
EABLO  
0
Reset:  
= Unimplemented or Reserved  
Figure 3-11 EEPROM Address Low Register (EADDRLO)  
All EABHI and EABLO bits read zero and are not writable in normal modes.  
All EABHI and EABLO bits are readable and writable in special modes.  
The MCU address bit AB0 is not stored in the EADDR registers since the EEPROM block is not byte  
addressable.  
3.3.10 EDATA — EEPROM Data Registers  
The EDATAHI and EDATALO registers are the EEPROM data registers.  
Address Offset: $_0A  
7
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
W
EDHI  
0
Reset:  
= Unimplemented or Reserved  
Figure 3-12 EEPROM Data High Register (EDATAHI)  
23  
For More Information On This Product,  
             
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Address Offset: $_0B  
7
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
W
EDLO  
0
Reset:  
= Unimplemented or Reserved  
Figure 3-13 EEPROM Data Low Register (EDATALO)  
All EDHI and EDLO bits read zero and are not writable in normal modes.  
All EDHI and EDLO bits are readable and writable in special modes.  
24  
For More Information On This Product,  
 
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Section 4 Functional Description  
4.1 EEPROM Command Operations  
Write and read operations are both used for the program, erase, erase verify, sector erase abort, and sector  
modify algorithms described in this section. The program, erase, and sector modify algorithms are  
controlled by a state machine whose timebase, EECLK, is derived from the oscillator clock via a  
programmable divider. The command register as well as the associated address and data registers operate  
as a buffer and a register (2-stage FIFO) so that a second command along with the necessary data and  
address can be stored to the buffer while the first command is still in progress. Buffer empty as well as  
command completion are signalled by flags in the EEPROM status register with interrupts generated, if  
enabled.  
The next sections describe:  
1. How to write the ECLKDIV register.  
2. Command write sequences to program, erase, erase verify, sector erase abort, and sector modify  
operations on the EEPROM memory.  
3. Valid EEPROM commands.  
4. Effects resulting from illegal EEPROM command write sequences or aborting EEPROM  
operations.  
4.1.1 Writing the ECLKDIV Register  
Prior to issuing any EEPROM command after a reset, the user is required to write the ECLKDIV register  
to divide the oscillator clock down to within the 150kHz to 200kHz range. Since the program and erase  
timings are also a function of the bus clock, the ECLKDIV determination must take this information into  
account.  
If we define:  
ECLK as the clock of the EEPROM timing control block,  
Tbus as the period of the bus clock,  
INT(x) as taking the integer part of x (e.g. INT(4.323)=4),  
then ECLKDIV register bits PRDIV8 and EDIV[5:0] are to be set as described in Figure 4-1.  
For example, if the oscillator clock frequency is 950kHz and the bus clock frequency is 10MHz,  
ECLKDIV bits EDIV[5:0] should be set to "4" (000100) and bit PRDIV8 set to "0". The resulting EECLK  
frequency is then 190kHz. As a result, the EEPROM program and erase algorithm timings are increased  
over the optimum target by:  
(200 190) ⁄ 200 × 100 = 5%  
If the oscillator clock frequency is 16MHz and the bus clock frequency is 40MHz, ECLKDIV bits  
EDIV[5:0] should be set to "50" (110010) and bit PRDIV8 set to "1". The resulting EECLK frequency is  
25  
For More Information On This Product,  
     
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
then 182kHz. In this case, the EEPROM program and erase algorithm timings are increased over the  
optimum target by:  
(200 182) ⁄ 200 × 100 = 9%  
NOTE: "4"Program and erase command execution time will increase proportionally with  
the period of EECLK.  
NOTE: Because of the impact of clock synchronization on the accuracy of the functional  
timings, programming or erasing the EEPROM memory cannot be performed if the  
bus clock runs at less than 1 MHz. Programming or erasing the EEPROM memory  
with EECLK < 150kHz should be avoided. Setting ECLKDIV to a value such that  
EECLK < 150kHz can destroy the EEPROM memory due to overstress. Setting  
ECLKDIV to a value such that (1/EECLK+Tbus) < 5µs can result in incomplete  
programming or erasure of the EEPROM memory cells.  
If the ECLKDIV register is written, the EDIVLD bit is set automatically. If the EDIVLD bit is zero, the  
ECLKDIV register has not been written since the last reset. If the ECLKDIV register has not been written  
to, the EEPROM command loaded during a command write sequence will not execute and the ACCERR  
flag in the ESTAT register will set.  
26  
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
START  
no  
Tbus < 1µs?  
ALL COMMANDS IMPOSSIBLE  
yes  
PRDIV8=0 (reset)  
no  
oscillator_clock  
12.8MHz?  
yes  
PRDIV8=1  
PRDCLK=oscillator_clock/8  
PRDCLK=oscillator_clock  
no  
PRDCLK[MHz]*(5+Tbus[µs])  
an integer?  
EDIV[5:0]=INT(PRDCLK[MHz]*(5+Tbus[µs]))  
yes  
EDIV[5:0]=PRDCLK[MHz]*(5+Tbus[µs])-1  
TRY TO DECREASE Tbus  
EECLK=(PRDCLK)/(1+EDIV[5:0])  
yes  
1/EECLK[MHz] + Tbus[µs] > 5  
END  
AND  
EECLK > 0.15MHz  
?
no  
yes  
EDIV[5:0] > 4?  
no  
ALL COMMANDS IMPOSSIBLE  
Figure 4-1 Determination Procedure for PRDIV8 and EDIV Bits  
27  
For More Information On This Product,  
 
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
4.1.2 Command Write Sequence  
The EEPROM command controller is used to supervise the command write sequence to execute program,  
erase, erase verify, sector erase abort, and sector modify algorithms.  
Before starting a command write sequence, the ACCERR and PVIOL flags in the ESTAT register must  
be clear (see section 3.3.6) and the CBEIF flag should be tested to determine the state of the address, data  
and command buffers. If the CBEIF flag is set, indicating the buffers are empty, a new command write  
sequence can be started. If the CBEIF flag is clear, indicating the buffers are not available, a new command  
write sequence will overwrite the contents of the address, data and command buffers.  
A command write sequence consists of three steps which must be strictly adhered to with writes to the  
EEPROM module not permitted between the steps. However, EEPROM register and array reads are  
allowed during a command write sequence. The basic command write sequence is as follows:  
1. Write to one address in the EEPROM memory.  
2. Write a valid command to the ECMD register.  
3. Clear the CBEIF flag in the ESTAT register by writing a “1” to CBEIF to launch the command.  
The address written in step 1 will be stored in the EADDR registers and the data will be stored in the  
EDATA registers. If the CBEIF flag in the ESTAT register is clear when the first EEPROM array write  
occurs, the contents of the address and data buffers will be overwritten and the CBEIF flag will be set.  
When the CBEIF flag is cleared, the CCIF flag is cleared on the same bus cycle by the EEPROM command  
controller indicating that the command was successfully launched. For all command write sequences  
except sector erase abort, the CBEIF flag will set four bus cycles after the CCIF flag is cleared indicating  
that the address, data, and command buffers are ready for a new command write sequence to begin. For  
sector erase abort operations, the CBEIF flag will remain clear until the operation completes. Except for  
the sector erase abort command, a buffered command will wait for the active operation to be completed  
before being launched. The sector erase abort command is launched when the CBEIF flag is cleared as part  
of a sector erase abort command write sequence. Once a command is launched, the completion of the  
command operation is indicated by the setting of the CCIF flag in the ESTAT register. The CCIF flag will  
set upon completion of all active and buffered commands .  
A command write sequence can be aborted prior to clearing the CBEIF flag in the ESTAT register by  
writing a “0” to the CBEIF flag and will result in the ACCERR flag in the ESTAT register being set. The  
ACCERR flag in the ESTAT register must be cleared prior to starting a new command write sequence.  
4.1.3 EEPROM Commands  
Table 4-1 summarizes the valid EEPROM commands along with the effects of the commands on the  
EEPROM block.  
Table 4-1 EEPROM Command Description  
ECMDB Command  
Function on EEPROM Memory  
Verify all memory bytes in the EEPROM block are erased.  
If the EEPROM block is erased, the BLANK flag in the ESTAT register will set upon  
command completion.  
Erase  
Verify  
$05  
28  
For More Information On This Product,  
     
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Table 4-1 EEPROM Command Description  
ECMDB Command  
Function on EEPROM Memory  
$20  
$40  
Program  
Program a word (two bytes) in the EEPROM block.  
Sector  
Erase  
Erase all four memory bytes in a sector of the EEPROM block.  
Erase all memory bytes in the EEPROM block.  
A mass erase of the full EEPROM block is only possible when EPOPEN and EPDIS bits  
in the EPROT register are set prior to launching the command.  
Mass  
Erase  
$41  
Abort the sector erase operation.  
The sector erase operation will terminate according to a set procedure. The EEPROM  
sector should not be considered erased if the ACCERR flag is set upon command  
completion.  
SectorErase  
Abort  
$47  
$60  
Sector  
Modify  
Erase all four memory bytes in a sector of the EEPROM block and reprogram the  
addressed word.  
NOTE: The user should not program an EEPROM word without first erasing the sector in  
which that word resides.  
4.1.3.1 Erase Verify Command  
The erase verify operation will verify that the EEPROM memory is erased.  
An example flow to execute the erase verify operation is shown in Figure 4-2. The erase verify command  
write sequence is as follows:  
1. Write to an EEPROM address to start the command write sequence for the erase verify command.  
The address and data written will be ignored.  
2. Write the erase verify command, $05, to the ECMD register.  
3. Clear the CBEIF flag in the ESTAT register by writing a “1” to CBEIF to launch the erase verify  
command.  
After launching the erase verify command, the CCIF flag in the ESTAT register will set after the operation  
has completed unless a new command write sequence has been buffered. The number of bus cycles  
required to execute the erase verify operation is equal to the number of words in the EEPROM memory  
plus 14 bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. Upon  
completion of the erase verify operation, the BLANK flag in the ESTAT register will be set if all addresses  
in the EEPROM memory are verified to be erased. If any address in the EEPROM memory is not erased,  
the erase verify operation will terminate and the BLANK flag in the ESTAT register will remain clear.  
29  
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
START  
Read: ECLKDIV register  
Clock Register  
Written  
Check  
NOTE: ECLKDIV needs to  
be set once after each reset.  
EDIVLD  
Set?  
no  
yes  
Write: ECLKDIV register  
Read: ESTAT register  
Address, Data,  
Command  
Buffer Empty Check  
CBEIF  
Set?  
no  
yes  
ACCERR/  
PVIOL  
Set?  
yes  
Access Error and  
Protection Violation  
Check  
Write: ESTAT register  
Clear ACCERR/PVIOL $30  
no  
Write: EEPROM Address  
and Dummy Data  
1.  
2.  
3.  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ECMD register  
Erase Verify Command $05  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ESTAT register  
Clear CBEIF $80  
Read: ESTAT register  
Bit Polling for  
Command Completion  
Check  
no  
no  
CCIF  
Set?  
yes  
Erase Verify  
Status  
BLANK  
Set?  
yes  
EEPROM Memory  
Erased  
EEPROM Memory  
Not Erased  
EXIT  
EXIT  
Figure 4-2 Example Erase Verify Command Flow  
4.1.3.2 Program Command  
The program operation will program a previously erased word in the EEPROM memory using an  
embedded algorithm.  
An example flow to execute the program operation is shown in Figure 4-3. The program command write  
sequence is as follows:  
1. Write to an EEPROM block address to start the command write sequence for the program  
command. The data written will be programmed to the address written.  
30  
For More Information On This Product,  
 
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
2. Write the program command, $20, to the ECMD register.  
3. Clear the CBEIF flag in the ESTAT register by writing a “1” to CBEIF to launch the program  
command.  
If a word to be programmed is in a protected area of the EEPROM memory, the PVIOL flag in the ESTAT  
register will set and the program command will not launch. Once the program command has successfully  
launched, the CCIF flag in the ESTAT register will set after the program operation has completed unless  
a new command write sequence has been buffered.  
31  
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
START  
Read: ECLKDIV register  
Clock Register  
Written  
Check  
NOTE: ECLKDIV needs to  
be set once after each reset.  
EDIVLD  
Set?  
no  
yes  
Write: ECLKDIV register  
Read: ESTAT register  
Address, Data,  
Command  
Buffer Empty Check  
CBEIF  
Set?  
no  
yes  
ACCERR/  
PVIOL  
Set?  
yes  
Access Error and  
Protection Violation  
Check  
Write: ESTAT register  
Clear ACCERR/PVIOL $30  
no  
Write: EEPROM Address  
and program Data  
1.  
2.  
3.  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ECMD register  
Program Command $20  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ESTAT register  
Clear CBEIF $80  
Read: ESTAT register  
Bit Polling for  
Buffer Empty  
Check  
no  
CBEIF  
Set?  
yes  
Sequential  
Programming  
Decision  
yes  
Next  
Word?  
no  
Read: ESTAT register  
Bit Polling for  
Command Completion  
Check  
no  
CCIF  
Set?  
yes  
EXIT  
Figure 4-3 Example Program Command Flow  
4.1.3.3 Sector Erase Command  
The sector erase operation will erase both words in a sector of EEPROM memory using an embedded  
algorithm.  
32  
For More Information On This Product,  
 
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
An example flow to execute the sector erase operation is shown in Figure 4-4. The sector erase command  
write sequence is as follows:  
1. Write to an EEPROM memory address to start the command write sequence for the sector erase  
command. The EEPROM address written determines the sector to be erased while global address  
bits [1:0] and the data written are ignored.  
2. Write the sector erase command, $40, to the ECMD register.  
3. Clear the CBEIF flag in the ESTAT register by writing a “1” to CBEIF to launch the sector erase  
command.  
If an EEPROM sector to be erased is in a protected area of the EEPROM memory, the PVIOL flag in the  
ESTAT register will set and the sector erase command will not launch. Once the sector erase command  
has successfully launched, the CCIF flag in the ESTAT register will set after the sector erase operation has  
completed unless a new command write sequence has been buffered.  
33  
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
START  
Read: ECLKDIV register  
Clock Register  
Written  
Check  
NOTE: ECLKDIV needs to  
be set once after each reset.  
EDIVLD  
Set?  
no  
yes  
Write: ECLKDIV register  
Read: ESTAT register  
Address, Data,  
Command  
Buffer Empty Check  
CBEIF  
Set?  
no  
yes  
ACCERR/  
PVIOL  
Set?  
yes  
Access Error and  
Protection Violation  
Check  
Write: ESTAT register  
Clear ACCERR/PVIOL $30  
no  
Write: EEPROM Sector Address  
and Dummy Data  
1.  
2.  
3.  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ECMD register  
Sector Erase Command $40  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ESTAT register  
Clear CBEIF $80  
Read: ESTAT register  
Bit Polling for  
Command Completion  
Check  
no  
CCIF  
Set?  
yes  
EXIT  
Figure 4-4 Example Sector Erase Command Flow  
4.1.3.4 Mass Erase Command  
The mass erase operation will erase all addresses in an EEPROM block using an embedded algorithm.  
An example flow to execute the mass erase operation is shown in Figure 4-5. The mass erase command  
write sequence is as follows:  
1. Write to an EEPROM memory address to start the command write sequence for the mass erase  
command. The address and data written will be ignored.  
2. Write the mass erase command, $41, to the ECMD register.  
3. Clear the CBEIF flag in the ESTAT register by writing a “1” to CBEIF to launch the mass erase  
command.  
34  
For More Information On This Product,  
 
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
If the EEPROM memory to be erased contains any protected area, the PVIOL flag in the ESTAT register  
will set and the mass erase command will not launch. Once the mass erase command has successfully  
launched, the CCIF flag in the ESTAT register will set after the mass erase operation has completed unless  
a new command write sequence has been buffered.  
START  
Read: ECLKDIV register  
Clock Register  
Written  
Check  
NOTE: ECLKDIV needs to  
be set once after each reset.  
EDIVLD  
Set?  
no  
yes  
Write: ECLKDIV register  
Read: ESTAT register  
Address, Data,  
Command  
Buffer Empty Check  
CBEIF  
Set?  
no  
yes  
ACCERR/  
PVIOL  
Set?  
yes  
Access Error and  
Protection Violation  
Check  
Write: ESTAT register  
Clear ACCERR/PVIOL $30  
no  
Write: EEPROM Address  
and Dummy Data  
1.  
2.  
3.  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ECMD register  
Mass Erase Command $41  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ESTAT register  
Clear CBEIF $80  
Read: ESTAT register  
Bit Polling for  
Command Completion  
Check  
no  
CCIF  
Set?  
yes  
EXIT  
Figure 4-5 Example Mass Erase Command Flow  
4.1.3.5 Sector Erase Abort Command  
The sector erase abort operation will terminate the active sector erase or sector modify operation so that  
other sectors in an EEPROM block are available for read and program operations without waiting for the  
sector erase or sector modify operation to complete.  
An example flow to execute the sector erase abort operation is shown in Figure 4-6. The sector erase abort  
command write sequence is as follows:  
35  
For More Information On This Product,  
   
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
1. Write to any EEPROM memory address to start the command write sequence for the sector erase  
abort command. The address and data written are ignored.  
2. Write the sector erase abort command, $47, to the ECMD register.  
3. Clear the CBEIF flag in the ESTAT register by writing a “1” to CBEIF to launch the sector erase  
abort command.  
If the sector erase abort command is launched resulting in the early termination of an active sector erase  
or sector modify operation, the ACCERR flag will set once the operation completes as indicated by the  
CCIF flag being set. The ACCERR flag sets to inform the user that the EEPROM sector may not be fully  
erased and a new sector erase or sector modify command must be launched before programming any  
location in that specific sector. If the sector erase abort command is launched but the active sector erase or  
sector modify operation completes normally, the ACCERR flag will not set upon completion of the  
operation as indicated by the CCIF flag being set. If the sector erase abort command is launched after the  
sector modify operation has completed the sector erase step, the program step will be allowed to complete.  
The maximum number of cycles required to abort a sector erase or sector modify operation is equal to four  
EECLK periods (see section 4.1.1) plus five bus cycles as measured from the time the CBEIF flag is  
cleared until the CCIF flag is set.  
NOTE: Since the ACCERR bit in the ESTAT register may be set at the completion of the  
sector erase abort operation, a command write sequence is not allowed to be  
buffered behind a sector erase abort command write sequence. The CBEIF flag will  
not set after launching the sector erase abort command to indicate that a command  
should not be buffered behind it. If an attempt is made to start a new command write  
sequence with a sector erase abort operation active, the ACCERR flag in the  
ESTAT register will be set. A new command write sequence may be started after  
clearing the ACCERR flag, if set.  
NOTE: The sector erase abort command should be used sparingly since a sector erase  
operation that is aborted counts as a complete program/erase cycle.  
36  
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Execute Sector Erase/Modify Command Flow  
Read: ESTAT register  
Erase  
Abort  
Needed?  
Bit Polling for  
Command  
Completion Check  
CCIF  
no  
no  
Set?  
yes  
yes  
Sector Erase  
Completed  
EXIT  
Write: Dummy EEPROM Address  
and Dummy Data  
1.  
2.  
3.  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ECMD register  
Sector Erase Abort Cmd $47  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ESTAT register  
Clear CBEIF $80  
Read: ESTAT register  
no  
Bit Polling for  
Command  
Completion Check  
CCIF  
Set?  
yes  
yes  
ACCERR  
Set?  
Access  
Error Check  
Write: ESTAT register  
Clear ACCERR $10  
no  
Sector Erase  
or Modify  
Completed  
Sector Erase  
or Modify  
Aborted  
EXIT  
EXIT  
Figure 4-6 Example Sector Erase Abort Command Flow  
4.1.3.6 Sector Modify Command  
The sector modify operation will erase both words in a sector of EEPROM memory followed by a  
reprogram of the addressed word using an embedded algorithm.  
An example flow to execute the sector modify operation is shown in Figure 4-7. The sector modify  
command write sequence is as follows:  
1. Write to an EEPROM memory address to start the command write sequence for the sector modify  
command. The EEPROM address written determines the sector to be erased and word to be  
reprogrammed while byte address bit 0 is ignored.  
37  
For More Information On This Product,  
 
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
2. Write the sector modify command, $60, to the ECMD register.  
3. Clear the CBEIF flag in the ESTAT register by writing a “1” to CBEIF to launch the sector erase  
command.  
If an EEPROM sector to be modified is in a protected area of the EEPROM memory, the PVIOL flag in  
the ESTAT register will set and the sector modify command will not launch. Once the sector modify  
command has successfully launched, the CCIF flag in the ESTAT register will set after the sector modify  
operation has completed unless a new command write sequence has been buffered.  
START  
Read: ECLKDIV register  
Clock Register  
Written  
Check  
NOTE: ECLKDIV needs to  
be set once after each reset.  
EDIVLD  
Set?  
no  
yes  
Write: ECLKDIV register  
Read: ESTAT register  
Address, Data,  
Command  
Buffer Empty Check  
CBEIF  
Set?  
no  
yes  
ACCERR/  
PVIOL  
Set?  
yes  
Access Error and  
Protection Violation  
Check  
Write: ESTAT register  
Clear ACCERR/PVIOL $30  
no  
Write: EEPROM Word Address  
and program Data  
1.  
2.  
3.  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ECMD register  
Sector Modify Command $60  
NOTE: command write sequence  
aborted by writing $00 to  
ESTAT register.  
Write: ESTAT register  
Clear CBEIF $80  
Read: ESTAT register  
Bit Polling for  
Command Completion  
Check  
no  
CCIF  
Set?  
yes  
EXIT  
Figure 4-7 Example Sector Modify Command Flow  
4.1.4 Illegal EEPROM Operations  
The ACCERR flag will be set during the command write sequence if any of the following illegal steps are  
performed, causing the command write sequence to immediately abort:  
38  
For More Information On This Product,  
     
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
1. Writing to an EEPROM address before initializing the ECLKDIV register.  
2. Writing a byte or misaligned word to a valid EEPROM address.  
3. Starting a command write sequence while a sector erase abort operation is active.  
4. Writing to any EEPROM register other than ECMD after writing to an EEPROM address.  
5. Writing a second command to the ECMD register in the same command write sequence.  
6. Writing an invalid command to the ECMD register.  
7. Writing to an EEPROM address after writing to the ECMD register.  
8. Writing to any EEPROM register other than ESTAT (to clear CBEIF) after writing to the ECMD  
register.  
9. Writing a “0” to the CBEIF flag in the ESTAT register to abort a command write sequence.  
The ACCERR flag will not be set if any EEPROM register is read during a valid command write sequence.  
The ACCERR flag will also be set if any of the following events occur:  
1. Launching the sector erase abort command while a sector erase or sector modify operation is active  
which results in the early termination of the sector erase or sector modify operation (see section  
4.1.3.5).  
2. The MCU enters STOP mode and a command operation is in progress. The operation is aborted  
immediately and any pending command is purged (see section 4.3).  
If the EEPROM memory is read during execution of an algorithm (CCIF = 0), the read operation will  
return invalid data and the ACCERR flag will not be set.  
If the ACCERR flag is set in the ESTAT register, the user must clear the ACCERR flag before starting  
another command write sequence (see section 3.3.6).  
The PVIOL flag will be set after the command is written to the ECMD register during a command write  
sequence if any of the following illegal operations are attempted, causing the command write sequence to  
immediately abort:  
1. Writing the program command if the address written in the command write sequence was in a  
protected area of the EEPROM memory.  
2. Writing the sector erase command if the address written in the command write sequence was in a  
protected area of the EEPROM memory.  
3. Writing the mass erase command to the EEPROM memory while any EEPROM protection is  
enabled.  
4. Writing the sector modify command if the address written in the command write sequence was in  
a protected area of the EEPROM memory.  
If the PVIOL flag is set in the ESTAT register, the user must clear the PVIOL flag before starting another  
command write sequence (see section 3.3.6).  
39  
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
4.2 Wait Mode  
If a command is active (CCIF=0) when the MCU enters the WAIT mode, the active command and any  
buffered command will be completed.  
The EEPROM module can recover the MCU from WAIT if the CBEIF and CCIF interrupts are enabled  
(see section 4.7).  
4.3 Stop Mode  
If a command is active (CCIF = 0) when the MCU enters the STOP mode, the operation will be aborted  
and, if the operation is program, sector erase, mass erase, or sector modify, the EEPROM array data being  
programmed or erased may be corrupted and the CCIF and ACCERR flags will be set. If active, the high  
voltage circuitry to the EEPROM memory will immediately be switched off when entering STOP mode.  
Upon exit from STOP, the CBEIF flag is set and any buffered command will not be launched. The  
ACCERR flag must be cleared before starting a command write sequence (see section 4.1.2).  
NOTE: As active commands are immediately aborted when the MCU enters STOP mode, it  
is strongly recommended that the user does not use the STOP command during  
program, sector erase, mass erase, or sector modify operations.  
4.4 Background Debug Mode  
In background debug mode (BDM), the EPROT register is writable. If the MCU is unsecured, then all  
EEPROM commands listed in Table 4-1 can be executed. If the MCU is secured and is in special single  
chip mode, the only command available to execute is mass erase.  
4.5 EEPROM Module Security  
The EEPROM module does not provide any security information to the MCU. After each reset, the  
security state of the MCU is a function of information provided by the Flash module (see the specific FTX  
Block Guide).  
4.5.1 Unsecuring the MCU in Special Single Chip Mode via the BDM  
Before the MCU can be unsecured in special single chip mode, the EEPROM memory must be erased  
using the following method:  
Reset the MCU into special single chip mode, delay while the erase test is performed by the BDM  
secure ROM, send BDM commands to disable protection in the EEPROM module, and execute a  
mass erase command write sequence to erase the EEPROM memory.  
After the CCIF flag sets to indicate that the EEPROM mass operation has completed and assuming that  
the Flash memory has also been erased, reset the MCU into special single chip mode. The BDM secure  
ROM will verify that the Flash and EEPROM memory are erased and will assert the UNSEC bit in the  
40  
For More Information On This Product,  
                 
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
BDM status register. This BDM action will cause the MCU to override the Flash security state and the  
MCU will be unsecured. Once the MCU is unsecured, BDM commands will be enabled and the Flash  
security byte may be programmed to the unsecure state.  
4.6 Resets  
4.6.1 EEPROM Reset Sequence  
On each reset, the EEPROM module executes a reset sequence to hold CPU activity while loading the  
EPROT register from the EEPROM memory according to Table 3-1.  
4.6.2 Reset While EEPROM Command Active  
If a reset occurs while any EEPROM command is in progress, that command will be immediately aborted.  
The state of a word being programmed or the sector / block being erased is not guaranteed.  
4.7 Interrupts  
The EEPROM module can generate an interrupt when all EEPROM command operations have completed,  
when the EEPROM address, data and command buffers are empty.  
Table 4-2 EEPROM Interrupt Sources  
Global (CCR)  
Interrupt Source  
Interrupt Flag  
Local Enable  
Mask  
EEPROM Address, Data and  
Command Buffers empty  
CBEIF  
(ESTAT register)  
CBEIE  
(ECNFG register)  
I-Bit  
CCIF  
(ESTAT register)  
CCIE  
(ECNFG register)  
All EEPROM commands completed  
I-Bit  
Vector addresses and their relative interrupt priority are determined at the MCU level.  
4.7.1 Description of EEPROM Interrupt Operation  
The logic used for generating interrupts is shown in Figure 4-8.  
The EEPROM module uses the CBEIF and CCIF flags in combination with the CBIE and CCIE enable  
bits to generate the EEPROM command interrupt request.  
41  
For More Information On This Product,  
             
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
CBEIF  
CBEIE  
EEPROM Command Interrupt Request  
CCIF  
CCIE  
Figure 4-8 EEPROM Interrupt Implementation  
For a detailed description of the register bits, refer to the EEPROM Configuration register and EEPROM  
Status register sections (see sections 3.3.4 and 3.3.6 respectively).  
42  
For More Information On This Product,  
 
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
–S–  
Index  
–W–  
–A–  
–B–  
–C–  
–E–  
–I–  
–K–  
–P–  
–R–  
Registers  
43  
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
44  
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
Block Guide End Sheet  
45  
For More Information On This Product,  
Freescale Semiconductor, Inc.  
Block Guide — S12EETX4KV0 V00.04  
FINAL PAGE OF  
46  
PAGES  
46  
For More Information On This Product,  

Motorola BRUTE H85XAH6JR5AN User Manual
Krups Coffeemaker XP2010 User Manual
JVC KD R35 User Manual
Intel 520 Series Mlc Solid State Drive SSDSC2CW480A301 User Manual
IBM iSeries 270 and 820 SENG 3002 01 User Manual
Fujitsu Computer Drive MHY2120BH User Manual
Freecom Technologies FHD 3 User Manual
Curtis SRCD247 User Manual
Black &amp; Decker DCM703C User Manual
Agilent Technologies Clock Radio 3A User Manual